SWITCHED RELUCTANCE MOTOR DRIVES
The switched reluctance drive was developed in the 1980s to oVer advan- tages in terms of eYciency, power per unit weight and volume, robustness and operational Xexibility. The motor and its associated power-electronic drive must be designed as an integrated package, and optimised for a particular speciWcation, e.g. for maximum overall eYciency with a
speciWc load, or maximum speed range, or peak short-term torque. Des- pite being relatively new, the technology has been applied to a wide range of applications including general-purpose industrial drives, compressors, domestic appliances and oYce and business equipment.
Principle of operation
The switched reluctance motor diVers from the conventional reluctance motor in that both the rotor and the stator have salient poles. This doubly salient arrangement (as shown in Figure 10.9) proves to be very eVective as far as electromagnetic energy conversion is concerned.
The stator carries coils on each pole, while the rotor, which is made from laminations in the usual way, has no windings or magnets and is therefore cheap to manufacture and extremely robust. The particular example shown in Figure 10.9 has 12 stator poles and 8 rotor poles, and represents a widely used arrangement, but other pole combinations are used to suit diVerent applications. In Figure 10.9, the 12 coils are grouped to form three phases, which are independently energised from a 3-phase converter.
The motor rotates by exciting the phases sequentially in the sequence A, B, C for anticlockwise rotation or A, C, B for clockwise rotation, the ‘nearest’ pair of rotor poles being pulled into alignment with the appropriate stator poles by reluctance torque action. In Figure 10.9 the four coils forming phase A are shown by thick line, the polarities of the coil MMFs being indicated by the letters N and S on the back of the core. Each time a new phase is excited the equilibrium position of the rotor advances by 158, so after one complete cycle (i.e. each of the three phases has been excited once) the angle turned through is 458. The machine therefore rotates once for eight fundamental cycles of supply to the stator windings, so in terms of the relationship between the fundamental supply frequency and the speed of rotation, the machine in Figure 10.9 behaves as a 16-pole conventional machine.
Readers familiar with stepping motors (see Chapter 9) will correctly identify the SR motor as a variable reluctance stepping motor. There are of course important design diVerences which reXect the diVerent object- ives (continuous rotation for the SR, stepwise progression for the step- per), but otherwise the mechanisms of torque production are identical. However, while the stepper is designed Wrst and foremost for open-loop operation, the SR motor is designed for self-synchronous operation, the phases being switched by signals derived from a shaft-mounted rotor position detector (RPT). In terms of performance, at all speeds below the base speed continuous operation at full torque is possible. Above the base speed, the Xux can no longer be maintained at full amplitude and the available torque reduces with speed. The operating characteristics are thus very similar to those of the other most important controlled- speed drives, but with the added advantage that overall eYciencies are generally a per cent or two higher.
Given that the mechanism of torque production in the switched reluc- tance motor appears to be very diVerent from that in d.c. machines, induction motors and synchronous machines (all of which exploit the ‘BIl ’ force on a conductor in a magnetic Weld) it might have been expected that one or other type would oVer such clear advantages that the other would fade away. In fact, despite claims and counter claims, there appears to be little to choose between them overall, and one wonders whether the mechanisms of operation are really so fundamentally diVerent as our ingrained ways of looking at things lead us to believe. Perhaps a visitor from another planet would note the similarity in terms of volume, quantities and disposition of iron and copper, and overall performance, and bring some fresh enlightenment to bear so that we emerge recognising some underlying truth that hitherto has escaped us.
Torque prediction and control
If the iron in the magnetic circuit is treated as ideal, analytical expressions can be derived to express the torque of a reluctance motor in terms of the rotor position and the current in the windings. In practice, however, this analysis is of little real use, not only because switched reluctance motors are designed to operate with high levels of magnetic saturation in parts of the magnetic circuit, but also because, except at low speeds, it is not practicable to achieve speciWed current proWles.
The fact that high levels of saturation are involved makes the problem of predicting torque at the design stage challenging, but despite the highly
non-linear relationships it is possible to compute the Xux, current and torque as functions of rotor position, so that optimum control strategies can be devised to meet particular performance speciWcations. Unfortu- nately this complexity means that there is no simple equivalent circuit available to illuminate behaviour.
As we saw when we discussed the stepping motor, to maximise the average torque it would (in principle) be desirable to establish the full current in each phase instantaneously, and to remove it instantaneously at the end of each positive torque period. But, as illustrated in Figure 9.14, this is not possible even with a small stepping motor, and certainly out of the question for switched reluctance motors (which have much higher inductance) except at low speeds where current chopping (see Figure 9.14) is employed. For most of the speed range, the best that can be done is to apply the full voltage available from the converter at the start of the ‘on’ period, and (using a circuit such as that shown in Figure 9.15) apply full negative voltage at the end of the pulse by opening both of the switches.
Operation using full positive voltage at the beginning and full negative voltage at the end of the ‘on’ period is referred to as ‘single-pulse’ opera- tion. For all but small motors (of less than say 1 kW) the phase resistance is negligible and consequently the magnitude of the phase Xux-linkage is determined by the applied voltage and frequency, as we have seen many times previously with other types of motor.
The relationship between the Xux-linkage (c) and the voltage is em- bodied in Faraday’s law, i.e. n ¼ dc=dt, so with the rectangular voltage waveform of single-pulse operation the phase Xux linkage waveforms have a very simple triangular shape, as in Figure 10.10 which shows the wave- forms for phase A of a 3-phase motor. (The waveforms for phases B and C are identical, but are not shown: they are displaced by one third and two thirds of a cycle, as indicated by the arrows.) The upper half of the diagram represents the situation at speed N, while the lower half corresponds to a speed of 2N. As can be seen, at the higher speed (high frequency) the ‘on’ period halves, so the amplitude of the Xux halves, leading to a reduction in available torque. The same limitation was seen in the case of the inverter- fed induction motor drive, the only diVerence being that the waveforms in that case were sinusoidal rather than triangular.
It is important to note that these Xux waveforms do not depend on the rotor position, but the corresponding current waveforms do because the MMF needed for a given Xux depends on the eVective reluctance of the magnetic circuit, and this of course varies with the position of the rotor.
To get the most motoring torque for any given phase Xux waveform, it is obvious that the rise and fall of the Xux must be timed to coincide
with the rotor position: ideally, the Xux should only be present when it produces positive torque, and be zero whenever it would produce nega- tive torque, but given the delay in build-up of the Xux it may be better to switch on early so that the Xux reaches a decent level at the point when it can produce the most torque, even if this does lead to some negative torque at the start and Wnish of the cycle.
The job of the torque control system is to switch each phase on and oV at the optimum rotor position in relation to the torque being demanded at the time, and this is done by keeping track of the rotor position using a RPT. Just what angles constitute the optimum depends on what is to be optimised (e.g. average torque, overall eYciency), and this in turn is decided by reference to the data stored digitally in the controller ‘memory map’ that relates current, Xux, rotor position and torque for the particular machine. Torque control is thus considerably less straightforward than in d.c. drives, where torque is directly
proportional to armature current, or induction motor drives where torque is proportional to slip.
Power converter and overall drive characteristics
An important diVerence between the SR motor and all other self- synchronous motors is that its full torque capability can be achieved without having to provide for both positive and negative currents in the phases. This is because the torque does not depend on the direction of current in the phase-winding. The advantage of such ‘unipolar’ drives is that because each of the main switching devices is permanently con- nected in series with one of the motor windings (as in Figure 9.15), there is no possibility of the ‘shoot-through’ fault (see Chapter 2) which is a major headache in the conventional inverter.
Overall closed-loop speed control is obtained in the conventional way with the speed error acting as a torque demand to the torque control system described above. However, in most cases it is not necessary to Wta tacho as the speed feedback signal can be derived from the RPT.
In common with other self-synchronous drives, a wide range of operating characteristics is available. If the input converter is fully controlled, continuous regeneration and full four-quadrant operation is possible, and the usual constant torque, constant power and series type characteristic is regarded as standard. Low speed torque can be uneven unless special measures are taken to proWle the current pulses, but continuous low speed operation is usually better than for most competing systems in terms of overall eYciency.